However, I've been reading up on the programmable iDATALINK Maestro RR adapter module. RPMS, Intake temp a whole bunch of stuff. My wife is getting me a Pioneer AVH-X5700BHS stereo head unit for Christmas. What would you like to know? I will look for the connector with the same wire colors. I've already identified the Metra CHTO-01 as the right adapter for this aftermarket head unit. Is the data gauge display actually accurate ?
I've already identified the Metra CHTO-01 as the right adapter for this aftermarket head unit. ). The new RR2 has the ability to work with 2018 and newer vehicles with a gateway at the OBD2, including Chrysler, Dodge and Jeep vehicles. Do not use T-Taps.
Not only is it supposed to turn on the amp and allow the steering wheel controls to work, but it also has some other cool … Discussion in 'Audio & Video' started by DBeistel, Jul 9, 2017. Here's the cable I ordered: Cable, J1962M Right Angle to Open, 6ft - OBD II Cables - Cables - OBD2Cables.com Attached is the wiring diagram. To contact the forum owner hit the Contact Us link.This site uses cookies. Even with out a flash you should still get at least RPMs.I actually contacted idatalink this morning.
INSTALL GUIDE WITH FO1 T-HARNESS RETAINS STEERING WHEEL CONTROLS, SYNCTM VOICE COMMANDS, SYNCTM BLUETOOTH, SIRIUSTM SATELLITE AND MORE!
I used the maestro to assign volume, next track, and phone call buttons on the steering wheel to functions on the radio.
that went on for a few hours before i noticed it. OLLGEN 60CM Ultra Slim 2 in 1 OBDII OBD2 Cable 16 Pin Female to Male/Female Extension Connector Cable Splitter,24Inch/2Feet 4.4 out of 5 stars 82. According to the rep I talked to at Maestro the "AUDIO CABLE" is for OEM chimes and sounds and the "AUX IN" is actually the OEM auxiliary integration. the question i have is how do i go about connecting the wires to the two obd slots it says "connect to twisted wire behind the connector" has anyone put in the maestro rr if so pictures would be great thanks in advance! They even updated it to work with the uconnect system too and display radio stations in the EVIC etc.My car was back there about 3 or 4 months ago and that was a feature that popped up when they were done with it, so maybe it's as simple as a firmware update on the unit. I know some of the Pioneers can but the rest of the functionality is lost with the Maestro. ... With newer cars implementing a gateway at the OBD2 connector, this is needed to enable the MRR2 to connect to three separate vehicle networks at the same time. JavaScript is disabled. $10.98. I haven't had any codes in my car so I'm not sure how that would display but a lot of info from the CAN network displays on there. Make sure the RED/BROWN wire is on PIN 6 and the YELLOW/ ... CONTROL CABLE MAESTRO RR MODULE PIONEER RADIO: ENSURE THAT NOTHING IS PLUGGED IN W/R PORT. Come join the discussion about performance, tuning, engine swaps, turbos, modifications, troubleshooting, maintenance, and more!https://www.amazon.ca/gp/product/B01M4K8N3C/ref=ox_sc_act_title_2?smid=AUYH9LCEC215V&psc=1. I used it to retain my steering wheel controls and factory mic. Connect RR A connector pin: ... 08 Brown/Yellow wire >> to OBD reader port pin 14 wire spliced directly spliced so pin6 still works with shop OBD reader ... Question6> should these be connected to the head units 16 pin connector and or the maestro connector A? Nah the OBD2 connector for the radio so you can get guages and TPMS info on the head unit is intermingled with a power wire for whatever reason in the Idatalink main harness (T02) so when the OBD info wire is connected it backfeeds constant power into the head unit.